Alloy A-286 is designed for applications requiring high strength and good corrosion resistance at temperatures up to 1300 °F(704 °C). This alloy offers high ductility in notched sections. In fact, the notched rupture strength of alloy A-286 is superior to many other commercial alloys with comparable high temperature properties.
AerMet 100 Data Sheet - Service Steel AerospaceAerMet® 100 ALLOY DATA SHEET AerMet® 100 is an ultra-high strength type of martenistic (a very hard form of steel crystalline structure) steel alloy. Is was developed in response to a need for a stronger and tougher material with superior fracture toughness and ductility. The alloy possesses a minimum
Alloy Steel The material has a high density and tensile strength but is costly to procure and use. It would work best under high stress conditions e. Material Ranking I. Based on Min weight i. Alloy Steel ii. Stainless Steel iii. Aluminum Alloy II. Based on Min Cost i. Stainless Steel ii. Aluminum Alloy iii. Alloy Steel f.
Carbon & High Strength Low Alloy (HSLA) Structural Steel Leeco ® Steel carries a deep inventory of carbon - or mild - steel plate as well as High Strength Low Alloy - or HSLA - steel plate. HSLA boasts a higher strength, lower weight and good machinability and ductility compared to conventional mild carbon steel grades. HSLA structural steels are manufactured to meet specific mechanical properties, such as hardness, strength, corrosion resistance
Cobalt MP159 Tech Steel & MaterialsCobalt MP159 is a Nickel-Cobalt based superalloy with a high concentration of cobalt and chromium designed to meet the advanced requirements of the aerospace industry. A member of the Multiphase family of alloys, MP159 possesses a rare mixture of ultra-high-tension strength, excellent ductility and surface stability, and excellent corrosion resistance.
ASTM A-572 (gr50/gr60/gr65) is a high strength, low alloy steel that offers greater strength than plain carbon steel plate, plus ductility, weldability, formability, toughness and fatigue strength. A572 meets a minimum strength requirement (dependent on grade) and provides good workability and weldability at
High Strength Low Alloy Steel DescriptionHigh Strength Low Alloy Steel This information provides repair recommendations and general guidelines for steel classified as High Strength Low Alloy Steel, also known as HSLA. This type of steel normally has a tensile strength range from 300-700 MPa. General Motors recommends the following when repairing or replacing this type of steel
Inconel® 718 Nickel Alloy Data Sheet CMC - BellwoodInconel® 718 is an age-hardenable Nickel-Chromium-Columbium (Niobium)-Molybdenum alloy with high strength, corrosion- resistance, and good fabrication characteristics. Inconel® 718 has high tensile, yield, and creep-rupture properties at high temperatures and can operate at cryogenic temperatures up to 1200°F (650°C).
Face-centered cubic (FCC) high-entropy alloys (HEAs) strengthened by coherent L1 2-nanoparticles exhibit an excellent strength-ductility balance.However, the strength of previously studied HEAs remains inadequate for the requirements of high-performance structural applications, due to their emphasis on coherency strengthening and the suppression of the formation of incoherent precipitates
Metallic Alloys (arranged by Density) - Alternate WarsThis is why tool steel, despite looking very attractive as a penetrator/armor material because of it's high strength levels, is not suited to the task because of it's very low ductility. The same goes for Depleted Uranium (0.75% Ti) Alloys which have been Gamma quenched and aged for 6 hours at 450C.
Metallurgical Materials Science and Alloy Design - High Owing to the nano-sized dispersion of the TiB2 particles of extreme stiffness and low density obtained by the in-situ formation with rapid solidification kinetics the new material has the mechanical performance of advanced high strength steels, and a 25% higher stiffness/density ratio than any of the currently used high strength steels
It is also possible to search for specific classes of steels such as low, medium, or high carbon steels, alloy steels, tool steels, stainless steel, etc. You can find typical values such as tensile strength, density, and thermal conductivity for steel alloys under the name Steels, General Properties. If you know the alloy number in which you
SAE AISI 4340 Steel Properties, Heat Treatment, Equivalent SAE AISI 4340 Steel (UNS G43400) AISI 4340 steel (UNS G43400) is an ultra-high strength medium carbon low alloy steel, which combines deep hardenability, high ductility, toughness and strength, and has high fatigue resistance and creep resistance.
TWIP, high Mn steel, austenitic steels, atom probe Most steels in this alloy category are in the System Fe-Mn-Al-C-Si. Specifically h igh-Mn steels attract much attention as lightweight steels due to their outstanding combination of strength and ductility caused by their high strain hardening capacity. Weight reduced variants of these high manganese austenitic steels are typically characterized by high manganese content (18 to 30 wt.%) and the
Authors challenged the research and development of super-high-strength low alloy steel seamless OCTG having compatibly im-proved sour (SSC) resistance to meet the market needs, and for the first time in the world, they realized practical application of the su-per-high strength sour (SSC) resistant low alloy OCTG of 125 ksi
Steel 300M Tech Steel & Materials300M is a low alloy, vacuum melted, steel of very high strength. Essentially it is a modified AISI 4340 steel with silicon, vanadium and slightly greater carbon and molybdenum content than 4340. 300M has a very good combination of strength (280 to 305 ksi), toughness, fatigue strength and good ductility. It is a through hardening alloy. Applications for 300M steel are those that require